How to put your SFA's headlights onto relays.
- SideKick
- LR4WD, Lockers, Crawler Gears
- Posts: 1127
- Joined: Wed Jan 12, 2011 12:45 pm
- Town: Cape Town
- Vehicle: Toyota Hilux '89 2.2 (4Y) EFI D/C 4x4, Mikem Suspension, PowerFlow Exhaust, BroSpeed Branch, 31" M/T, Long Range Fuel Tank, Front Diff-Lock
- Real Name: Stephan
- Club VHF Licence: X108
- Location: Parow
How to put your SFA's headlights onto relays.
Hi guys
I did mine recently and here is a how to guide for those wanting to do the same. Don't know if you guys want to add this as a sticky or something somewhere.
The most important thing to know is that the lights are wired up negatively, if that is the correct term. The switch isn't between the battery and the light like you would think. The switch is between the lighs and the earth. So to put your lights onto relays, you have to wire everything in reverse (earth and live gets swopped).
Here is how the factory wired it: (Only the relevant wires are in colour. The black wires aren't apllicable, you never touch them)
And here is how you re-wire it onto relays:
Basicly you rewire the existing wires from the lights to the relays, and you lay new wire for the lighs from the battery and to the earth.
What you need is:
New wire:
I got 3mm wire for the common wire from the battery to the lights, and I got 4 different colour 2.5mm wires from the two low and high beams to the relay. And then I got 2.5mm wire from the relay to the earth (Should've been 3mm wire).
2 x relays. I got two 5 pin normal open dual output relays so that I can run one cable straight to each light on both low and hight beam and I don't have to splice any cables. I got one Hella relay and one Bosch relay just for the kick of it so see if there's any difference (no difference so far and they cost the same at autozone).
Then I got two inline fuses:
My H4 connectors looked a bit bad being 24 year old and all, so I decided to replace them while I'm at it. The problem now is that no matter what H4 connector you buy, they all come with crap thin wire which will make your new thick wiring redundant. Here is the difference between 2.5mm wire and the crap wire that comes with the H4 connector:
The more expensive H4 connectors can't be taken appart to replace the thin wires, so I got the elcheapo ones, took them appart and put in proper wires.
When I was done with that, I got some car silicone and sealed them up nicely. It's doesn't look so great I guess, but they will work great!!!
I did mine recently and here is a how to guide for those wanting to do the same. Don't know if you guys want to add this as a sticky or something somewhere.
The most important thing to know is that the lights are wired up negatively, if that is the correct term. The switch isn't between the battery and the light like you would think. The switch is between the lighs and the earth. So to put your lights onto relays, you have to wire everything in reverse (earth and live gets swopped).
Here is how the factory wired it: (Only the relevant wires are in colour. The black wires aren't apllicable, you never touch them)
And here is how you re-wire it onto relays:
Basicly you rewire the existing wires from the lights to the relays, and you lay new wire for the lighs from the battery and to the earth.
What you need is:
New wire:
I got 3mm wire for the common wire from the battery to the lights, and I got 4 different colour 2.5mm wires from the two low and high beams to the relay. And then I got 2.5mm wire from the relay to the earth (Should've been 3mm wire).
2 x relays. I got two 5 pin normal open dual output relays so that I can run one cable straight to each light on both low and hight beam and I don't have to splice any cables. I got one Hella relay and one Bosch relay just for the kick of it so see if there's any difference (no difference so far and they cost the same at autozone).
Then I got two inline fuses:
My H4 connectors looked a bit bad being 24 year old and all, so I decided to replace them while I'm at it. The problem now is that no matter what H4 connector you buy, they all come with crap thin wire which will make your new thick wiring redundant. Here is the difference between 2.5mm wire and the crap wire that comes with the H4 connector:
The more expensive H4 connectors can't be taken appart to replace the thin wires, so I got the elcheapo ones, took them appart and put in proper wires.
When I was done with that, I got some car silicone and sealed them up nicely. It's doesn't look so great I guess, but they will work great!!!
Last edited by SideKick on Sun Jul 08, 2012 10:22 pm, edited 2 times in total.
Stress:
The confusion created when one's mind overrides the body's desire to choke the living $H!t out of some asshole that desperately deserves it!
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
![Irate :irate:](./images/smilies/ireful.gif)
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
- SideKick
- LR4WD, Lockers, Crawler Gears
- Posts: 1127
- Joined: Wed Jan 12, 2011 12:45 pm
- Town: Cape Town
- Vehicle: Toyota Hilux '89 2.2 (4Y) EFI D/C 4x4, Mikem Suspension, PowerFlow Exhaust, BroSpeed Branch, 31" M/T, Long Range Fuel Tank, Front Diff-Lock
- Real Name: Stephan
- Club VHF Licence: X108
- Location: Parow
Re: How to put your SFA's headlights onto relays.
Here is how the connectors looked in the end:
Not TOO bad . . .
Anyway. So I pulled out all the wiring from the lights all the way back to my fuse box.
Those 4 wires you end up with that used to go to the lights, you then wire up to the two relays according to my diagram.
You then take your new wires and you wire them together with the inline fuses according to my diagram. Remember, this gets wired in reverse on your relays. Your outputs are actually your inputs from your lights and your input is actually your output to your earth. (If you use a 4 pin relay and have both lights connected to the one pin, then it doesn't matter which way around you wire them)
And that's it. There isn't much to explain there . . . wiring is wiring. Oh yes, I forgot to add terminals to the list of things needed!!!
Anyway. Mine is an extreme case I think as my headlights sucked, but here is my before:
And here is my after:
Also, please note that I do not know how this will affect aftermarket spotlights as I still have to check it myself. Will add it here in a day or two once I know.
EDIT - Replaced my spotlights' faulty relay and spots are working!
Not TOO bad . . .
Anyway. So I pulled out all the wiring from the lights all the way back to my fuse box.
Those 4 wires you end up with that used to go to the lights, you then wire up to the two relays according to my diagram.
You then take your new wires and you wire them together with the inline fuses according to my diagram. Remember, this gets wired in reverse on your relays. Your outputs are actually your inputs from your lights and your input is actually your output to your earth. (If you use a 4 pin relay and have both lights connected to the one pin, then it doesn't matter which way around you wire them)
And that's it. There isn't much to explain there . . . wiring is wiring. Oh yes, I forgot to add terminals to the list of things needed!!!
Anyway. Mine is an extreme case I think as my headlights sucked, but here is my before:
And here is my after:
Also, please note that I do not know how this will affect aftermarket spotlights as I still have to check it myself. Will add it here in a day or two once I know.
EDIT - Replaced my spotlights' faulty relay and spots are working!
Last edited by SideKick on Mon Jul 09, 2012 6:29 pm, edited 1 time in total.
Stress:
The confusion created when one's mind overrides the body's desire to choke the living $H!t out of some asshole that desperately deserves it!
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
![Irate :irate:](./images/smilies/ireful.gif)
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
- Donkey
- Monster Truck
- Posts: 5132
- Joined: Fri Oct 30, 2009 12:33 am
- Town: Johannesburg
- Vehicle: 2002 3.0KZ-TE 4x4, Eazyawn RTT, Snorkel, NudgeM Bumper, 38mm Ball Joint Spacers, 35" Maxxis Bighorns, Dastek Unichip, 60 ltr Snomaster fridge/freezer, 40mm body lift, Mikem front/rear with extended shackles, Bilsteins shox rear
- Real Name: Tumelo Thebe aka Baas John
- Club VHF Licence: X122
Re: How to put your SFA's headlights onto relays.
Well done
Stephan, pic with wires all oose and looking messy looks similar, that's all I'm seeing last week and this one coming.
Why did you have to change them onto relays?![Thinking :think:](./images/smilies/icon_think.gif)
![Clapping :clap:](./images/smilies/icon_clap.gif)
Why did you have to change them onto relays?
![Thinking :think:](./images/smilies/icon_think.gif)
Tumelo Maketekete
Donkey, simple and often misunderstood.
We don't stop playing because we grow old, but we grow old because we stop playing!
2002 - 3.0KZ-TE Toyota Hilux (Letebele)
1994 - 1.6i Gl Toyota Corolla (Platkar)
1990 - Gli TwinCam 16v (ZuluBoy)
![Image](http://www.hilux4x4.co.za/views/download/file.php?id=41541)
![Image](http://www.hilux4x4.co.za/views/download/file.php?id=41561)
Donkey, simple and often misunderstood.
We don't stop playing because we grow old, but we grow old because we stop playing!
2002 - 3.0KZ-TE Toyota Hilux (Letebele)
1994 - 1.6i Gl Toyota Corolla (Platkar)
1990 - Gli TwinCam 16v (ZuluBoy)
- Mud Dog
- Moderator
- Posts: 29858
- Joined: Tue Apr 29, 2008 2:18 am
- Town: East London
- Vehicle: '90 SFA Hilux DC 4X4, Full OME, 110mm lift. Brospeed branch, 50mm ss freeflow exhaust. 30 x 9.5 Discoverer S/T's on Viper mags. L/R tank. (AWOL) '98 LTD 2.4 SFA, dual battery system. Dobinson suspension, LR tanks, 31" BF mud's.
- Real Name: Andy
- Club VHF Licence: HC103
Re: How to put your SFA's headlights onto relays.
Was done to increase the voltage / power supply to the lights via thicker and more direct wiring.Donkey wrote:Well doneStephan, pic with wires all oose and looking messy looks similar, that's all I'm seeing last week and this one coming.
Why did you have to change them onto relays?
![Wink ;-)](./images/smilies/icon_e_wink.gif)
When your road comes to an end ...... you need a HILUX!.
![Image](http://www.hilux4x4.co.za/signatures/SIG_03.JPG)
![Image](http://www.hilux4x4.co.za/signatures/SIG_04.JPG)
Life is like a jar of Jalapeño peppers ... what you do today, might burn your ass tomorrow.
Don't take life too seriously ..... no-one gets out alive.
It's not about waiting for storms to pass. It's about learning to dance in the rain.
And be yourself ..... everyone else is taken!
Life is like a jar of Jalapeño peppers ... what you do today, might burn your ass tomorrow.
Don't take life too seriously ..... no-one gets out alive.
It's not about waiting for storms to pass. It's about learning to dance in the rain.
And be yourself ..... everyone else is taken!
- Rooies
- LR 4WD Rear Locker
- Posts: 378
- Joined: Wed Apr 07, 2010 12:05 pm
- Town: Strand
- Vehicle: 1994 2.4i (22RE) D/C Raider 4X4
- Real Name: Rudi
Re: How to put your SFA's headlights onto relays.
Good job Stephan,
I can see whats going to keep me busy next week. Well explained.
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
I can see whats going to keep me busy next week. Well explained.
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
ROOIES: 1994 2.4i (22RE) Raider D/C - 200 000kms - Brospeed Branch & Powerflow Exhaust
MIKEM Suspension & Gabriel Safari Shocks - "31 BF Goodrich AT - GOMAD Aluminium Canopy
Melvill & Moon Seat Covers - Safari Snorkel - Bushwakka Weekender Offroad Trailer
![Image](http://i884.photobucket.com/albums/ac45/rooies/4X4/Rooies.jpg)
MIKEM Suspension & Gabriel Safari Shocks - "31 BF Goodrich AT - GOMAD Aluminium Canopy
Melvill & Moon Seat Covers - Safari Snorkel - Bushwakka Weekender Offroad Trailer
![Image](http://i884.photobucket.com/albums/ac45/rooies/4X4/Rooies.jpg)
- SideKick
- LR4WD, Lockers, Crawler Gears
- Posts: 1127
- Joined: Wed Jan 12, 2011 12:45 pm
- Town: Cape Town
- Vehicle: Toyota Hilux '89 2.2 (4Y) EFI D/C 4x4, Mikem Suspension, PowerFlow Exhaust, BroSpeed Branch, 31" M/T, Long Range Fuel Tank, Front Diff-Lock
- Real Name: Stephan
- Club VHF Licence: X108
- Location: Parow
Re: How to put your SFA's headlights onto relays.
Update
I replaced my spotlights' faulty relay and spots are working!
I replaced my spotlights' faulty relay and spots are working!
Stress:
The confusion created when one's mind overrides the body's desire to choke the living $H!t out of some asshole that desperately deserves it!
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
![Irate :irate:](./images/smilies/ireful.gif)
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
- Stef
- Monster Truck
- Posts: 3125
- Joined: Mon Jan 25, 2010 12:54 pm
- Town: Pretoria
- Vehicle: '98 LTD
- Real Name: Stefan
- Club VHF Licence: X107
Re: How to put your SFA's headlights onto relays.
Nice write-up
One thing to add I think, is 2 diodes across the relay coils, i.e. one diode across pins 85 & 88 on each relay with the cathodes on the fusebox side (R-B & R-W in your diagram).
This is to counter back EMF from the relay coils so that you don't get arcing on the stalk contacts.![Wink ;-)](./images/smilies/icon_e_wink.gif)
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
One thing to add I think, is 2 diodes across the relay coils, i.e. one diode across pins 85 & 88 on each relay with the cathodes on the fusebox side (R-B & R-W in your diagram).
This is to counter back EMF from the relay coils so that you don't get arcing on the stalk contacts.
![Wink ;-)](./images/smilies/icon_e_wink.gif)
- SideKick
- LR4WD, Lockers, Crawler Gears
- Posts: 1127
- Joined: Wed Jan 12, 2011 12:45 pm
- Town: Cape Town
- Vehicle: Toyota Hilux '89 2.2 (4Y) EFI D/C 4x4, Mikem Suspension, PowerFlow Exhaust, BroSpeed Branch, 31" M/T, Long Range Fuel Tank, Front Diff-Lock
- Real Name: Stephan
- Club VHF Licence: X108
- Location: Parow
Re: How to put your SFA's headlights onto relays.
English please?Stef wrote:Nice write-up![]()
One thing to add I think, is 2 diodes across the relay coils, i.e. one diode across pins 85 & 88 on each relay with the cathodes on the fusebox side (R-B & R-W in your diagram).
This is to counter back EMF from the relay coils so that you don't get arcing on the stalk contacts.
Stress:
The confusion created when one's mind overrides the body's desire to choke the living $H!t out of some asshole that desperately deserves it!
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
![Irate :irate:](./images/smilies/ireful.gif)
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
- Rider
- Low Range 4WD
- Posts: 232
- Joined: Wed Aug 03, 2011 6:17 pm
- Town: Richards Bay
- Vehicle: 1987 Toyota Hilux 4x4 d/c 40mm body lift, KZ-TE Diff with Diff lock, Snorkel, 31" AT tyres , Powered by FORD 3.0 V6 uprated.
- Real Name: Luke
- Location: Richards bay
Re: How to put your SFA's headlights onto relays.
a diode has 2 legs .Anode(+) and cathode(-)-(silver ring)
EMF-electro motive force
Im not sure if he wants you to keep the current constant :?
lets wait for his reply![Surrender :surrender:](./images/smilies/surrender.gif)
EMF-electro motive force
Im not sure if he wants you to keep the current constant :?
lets wait for his reply
![Surrender :surrender:](./images/smilies/surrender.gif)
![Image](http://i971.photobucket.com/albums/ae192/519franco/23072010019-001-1-4.jpg)
PROUD OWNER OF A TOYOTA HILUX AKA AMA-HIPZ
- cprinsloo
- LR 4WD Full Lockers
- Posts: 859
- Joined: Sun Jul 15, 2007 6:00 pm
- Town: Nelspruit
- Vehicle: 1998 D/C 4x4
- Real Name: Chris
- Club VHF Licence: X52
- Location: Mpumalanga
Re: How to put your SFA's headlights onto relays.
Any coil will have energy when it is energised (hence the term!). When the circuit is opened, the energy will dissipate over the switch contacts with a spark, which can eventually erode the contacts. The solution is to place a diode over the coil, as shown, then the energy is dissipated through the coil resistance. It is known as a flyback or freewheel diode.
http://en.wikipedia.org/wiki/Flyback_diode" onclick="window.open(this.href);return false;
Cheers,
C
http://en.wikipedia.org/wiki/Flyback_diode" onclick="window.open(this.href);return false;
Cheers,
C
1998 Hilux D/C Lexus VVTi
- BosveldBul
- Low Range 4WD
- Posts: 146
- Joined: Fri Feb 11, 2011 10:42 am
- Town: Centurion
- Vehicle: Hilux 3.0 D4-D 4x4
- Real Name: Jak
How to put your SFA's headlights onto relays.
So can I do this on my '86 corolla too? Will I use the same relays etc?
- pietpetoors
- Moderator
- Posts: 10650
- Joined: Thu May 17, 2007 9:12 pm
- Town: Langebaan
- Vehicle: 2.7 Hilux 4x4 DC
- Real Name: Pieter
- Club VHF Licence: X27
- Contact:
Re: How to put your SFA's headlights onto relays.
I ordered some wiring looms for this. They already have all the relays and plugs. Just plug in and connect to the battery.
Only thing they don't have is that diode box for the blue light on dashboard.
Still waiting for payment to clear and then the long wait to import, but I think they should be here by Mid August
Price I still have to see, might be in the region of R350.00
Only thing they don't have is that diode box for the blue light on dashboard.
Still waiting for payment to clear and then the long wait to import, but I think they should be here by Mid August
Price I still have to see, might be in the region of R350.00
Only Dead Fish Go With The Flow!
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
- SideKick
- LR4WD, Lockers, Crawler Gears
- Posts: 1127
- Joined: Wed Jan 12, 2011 12:45 pm
- Town: Cape Town
- Vehicle: Toyota Hilux '89 2.2 (4Y) EFI D/C 4x4, Mikem Suspension, PowerFlow Exhaust, BroSpeed Branch, 31" M/T, Long Range Fuel Tank, Front Diff-Lock
- Real Name: Stephan
- Club VHF Licence: X108
- Location: Parow
Re: How to put your SFA's headlights onto relays.
Hold on there guys.
Please scroll back up and see that I did my headlights on relays, and added my spotlights on their relays, and the high beam indicator is working. Everything 100% all without diodes or coils or any of these complicated things you are talking about . . . I just wired it up like in my diagram . . .
Please scroll back up and see that I did my headlights on relays, and added my spotlights on their relays, and the high beam indicator is working. Everything 100% all without diodes or coils or any of these complicated things you are talking about . . . I just wired it up like in my diagram . . .
Stress:
The confusion created when one's mind overrides the body's desire to choke the living $H!t out of some asshole that desperately deserves it!
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
![Irate :irate:](./images/smilies/ireful.gif)
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
- pietpetoors
- Moderator
- Posts: 10650
- Joined: Thu May 17, 2007 9:12 pm
- Town: Langebaan
- Vehicle: 2.7 Hilux 4x4 DC
- Real Name: Pieter
- Club VHF Licence: X27
- Contact:
Re: How to put your SFA's headlights onto relays.
Stephan, I will see when those looms arrive here. The manufacturer assured me that it works on all vehicles without any problems. So if it works correctly it will be a bonus, I hope it does.
Only Dead Fish Go With The Flow!
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
- Family_Dog
- Moderator
- Posts: 12697
- Joined: Tue May 22, 2007 10:09 am
- Town: Klerksdorp
- Vehicle: Hilux DC SFA, Hilux 2.7 DC, Hilux 2.7 SC, Prado 95 VX
- Real Name: Eric
- Club VHF Licence: HC101
- Location: Klerksdorp, NW
- Contact:
Re: How to put your SFA's headlights onto relays.
cprinsloo wrote:Any coil will have energy when it is energised (hence the term!). When the circuit is opened, the energy will dissipate over the switch contacts with a spark, which can eventually erode the contacts. The solution is to place a diode over the coil, as shown, then the energy is dissipated through the coil resistance. It is known as a flyback or freewheel diode.
http://en.wikipedia.org/wiki/Flyback_diode" onclick="window.open(this.href);return false;
Cheers,
C
Unless you are operating the relay coil with a solid state device which can be destroyed by the induced EMF (unlikely with a SFA!!), I would not bother with the diode. It is used in high-energy circuits (the TV flyback example above, which "switches" on & off 15,625 times a second) but in this case, nothing fancy, and all it would protect is the actual original light switch contacts which were built to handle high amperage in the first place. The relay coil draws minimal current.
-F_D
![Image](http://www.audiokarma.org/forums/images/smilies/pawprint.gif)
White Fang: 1999 2.7i DC Raider 4x4
Bull Dog: 1987 4Y-EFI 2.2 DC 4x4
Pra Dog: 1998 Prado VX 3.4
Hound Dog: 2000 2.7i SC 4x4
One Staffie, One Jack Russell, One Ring Neck Screecher, 17 Fish of questionable heritage
![Image](https://i.postimg.cc/9fGpmSTW/4-in-1-Signature.jpg)
- pietpetoors
- Moderator
- Posts: 10650
- Joined: Thu May 17, 2007 9:12 pm
- Town: Langebaan
- Vehicle: 2.7 Hilux 4x4 DC
- Real Name: Pieter
- Club VHF Licence: X27
- Contact:
Re: How to put your SFA's headlights onto relays.
I received some of those harnesses today. They are very well made and comes complete with 2x relays.
I installed mine in 10 minutes.
Only problem is, the blue light on dash is not working so I will have to build the little box Cassie was talking about.
Light meter readings:
I just use it for comparison values. The light is very uneven, so I tried to get the brightest spot one meter from the light.
Values was on the 10,000 scale on light meter.
Before:
Dim = 620
Bright = 810
After:
Dim = 860
Bright = 1050
Above is with Osram nightbreakers
I installed mine in 10 minutes.
Only problem is, the blue light on dash is not working so I will have to build the little box Cassie was talking about.
Light meter readings:
I just use it for comparison values. The light is very uneven, so I tried to get the brightest spot one meter from the light.
Values was on the 10,000 scale on light meter.
Before:
Dim = 620
Bright = 810
After:
Dim = 860
Bright = 1050
Above is with Osram nightbreakers
Only Dead Fish Go With The Flow!
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
- pietpetoors
- Moderator
- Posts: 10650
- Joined: Thu May 17, 2007 9:12 pm
- Town: Langebaan
- Vehicle: 2.7 Hilux 4x4 DC
- Real Name: Pieter
- Club VHF Licence: X27
- Contact:
Re: How to put your SFA's headlights onto relays.
For those who cannot wait for us to manufacture the fix, I added it to my shop so long.
I've put it up at a lower price as originally planned. When we get the fix we will sell it is a separate plugin unit for the vehicle which need it.
The harness is at
http://www.4x4direct.co.za/shop/index.p ... cts_id=394" onclick="window.open(this.href);return false;
I see most places recommend a 30A relay for up to 100 watt, I bought some 40A relays just to make sure they last longer.
I opted for 5 pin, do same work as 4 pin, only one pin you ignore if you need 4 pin.
Relays at
http://www.4x4direct.co.za/shop/index.p ... cts_id=393" onclick="window.open(this.href);return false;
For the guys who wants to build their own I have H4 plugs
http://www.4x4direct.co.za/shop/index.p ... cts_id=391" onclick="window.open(this.href);return false;
And sockets to fit the 5 pin relay, no more loose wires
http://www.4x4direct.co.za/shop/index.p ... cts_id=392" onclick="window.open(this.href);return false;
I've put it up at a lower price as originally planned. When we get the fix we will sell it is a separate plugin unit for the vehicle which need it.
The harness is at
http://www.4x4direct.co.za/shop/index.p ... cts_id=394" onclick="window.open(this.href);return false;
I see most places recommend a 30A relay for up to 100 watt, I bought some 40A relays just to make sure they last longer.
I opted for 5 pin, do same work as 4 pin, only one pin you ignore if you need 4 pin.
Relays at
http://www.4x4direct.co.za/shop/index.p ... cts_id=393" onclick="window.open(this.href);return false;
For the guys who wants to build their own I have H4 plugs
http://www.4x4direct.co.za/shop/index.p ... cts_id=391" onclick="window.open(this.href);return false;
And sockets to fit the 5 pin relay, no more loose wires
http://www.4x4direct.co.za/shop/index.p ... cts_id=392" onclick="window.open(this.href);return false;
Only Dead Fish Go With The Flow!
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
- MOFASA
- Monster Truck
- Posts: 3095
- Joined: Sun Mar 04, 2012 7:27 pm
- Town: Kempton Park
- Vehicle: 1998 JEEP XJ 4.0............ 4 inch lift.... more mods to follow............ Old vehicle was MOFASA
- Real Name: Johno
- Club VHF Licence: X119
- Location: Kempton Park
Re: How to put your SFA's headlights onto relays.
pietpetoors wrote:I received some of those harnesses today. They are very well made and comes complete with 2x relays.
I installed mine in 10 minutes.
Only problem is, the blue light on dash is not working so I will have to build the little box Cassie was talking about.
Light meter readings:
I just use it for comparison values. The light is very uneven, so I tried to get the brightest spot one meter from the light.
Values was on the 10,000 scale on light meter.
Before:
Dim = 620
Bright = 810
After:
Dim = 860
Bright = 1050
Above is with Osram nightbreakers
![Thread is worthless without pics :ttwwp:](./images/smilies/ttiwwp.gif)
Pics and Price PLEASE.......
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
Live Life in the FAST lane....
Forget the past, Embrace the FUTURE!!!!
To 4x4 or not to 4x4 thats the question....
IT'S A JEEP
..... You wouldn't understand....
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/HCMU_zps9dc3a722.jpg)
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/f2b7db67-c22d-488c-b2b7-bf53164312b2_zpsf210db12.jpg)
[rimg=206x128]
Forget the past, Embrace the FUTURE!!!!
To 4x4 or not to 4x4 thats the question....
IT'S A JEEP
![Yahoo :yahoo:](./images/smilies/yahoo.gif)
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/HCMU_zps9dc3a722.jpg)
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/f2b7db67-c22d-488c-b2b7-bf53164312b2_zpsf210db12.jpg)
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/Uniteagainstpoaching_zpsf4c81906.jpg)
- CasKru
- Moderator
- Posts: 23956
- Joined: Tue Dec 04, 2007 11:52 am
- Town: Benoni
- Vehicle: '94 Hilux Raider 2.4i (22RE) DC 4x4
- Real Name: Cassie
- Club VHF Licence: B15
- Location: Rynfield
Re: How to put your SFA's headlights onto relays.
Now if you followed the links you would have seen thisMOFASA wrote:pietpetoors wrote:I received some of those harnesses today. They are very well made and comes complete with 2x relays.
I installed mine in 10 minutes.
Only problem is, the blue light on dash is not working so I will have to build the little box Cassie was talking about.
Light meter readings:
I just use it for comparison values. The light is very uneven, so I tried to get the brightest spot one meter from the light.
Values was on the 10,000 scale on light meter.
Before:
Dim = 620
Bright = 810
After:
Dim = 860
Bright = 1050
Above is with Osram nightbreakers![]()
Pics and Price PLEASE.......![]()
![Twisted Evil :twisted:](./images/smilies/icon_twisted.gif)
![Image](http://www.4x4direct.co.za/shop/images/h4-harness.jpg)
To God be the glory
- MOFASA
- Monster Truck
- Posts: 3095
- Joined: Sun Mar 04, 2012 7:27 pm
- Town: Kempton Park
- Vehicle: 1998 JEEP XJ 4.0............ 4 inch lift.... more mods to follow............ Old vehicle was MOFASA
- Real Name: Johno
- Club VHF Licence: X119
- Location: Kempton Park
Re: How to put your SFA's headlights onto relays.
CasKru wrote:Now if you followed the links you would have seen this
![Slap :slap:](./images/smilies/slap.gif)
![Surrender :surrender:](./images/smilies/surrender.gif)
![Surrender :surrender:](./images/smilies/surrender.gif)
![Surrender :surrender:](./images/smilies/surrender.gif)
Live Life in the FAST lane....
Forget the past, Embrace the FUTURE!!!!
To 4x4 or not to 4x4 thats the question....
IT'S A JEEP
..... You wouldn't understand....
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/HCMU_zps9dc3a722.jpg)
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/f2b7db67-c22d-488c-b2b7-bf53164312b2_zpsf210db12.jpg)
[rimg=206x128]
Forget the past, Embrace the FUTURE!!!!
To 4x4 or not to 4x4 thats the question....
IT'S A JEEP
![Yahoo :yahoo:](./images/smilies/yahoo.gif)
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/HCMU_zps9dc3a722.jpg)
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/f2b7db67-c22d-488c-b2b7-bf53164312b2_zpsf210db12.jpg)
![Image](http://i1284.photobucket.com/albums/a577/MOFASA1975/Uniteagainstpoaching_zpsf4c81906.jpg)
- SideKick
- LR4WD, Lockers, Crawler Gears
- Posts: 1127
- Joined: Wed Jan 12, 2011 12:45 pm
- Town: Cape Town
- Vehicle: Toyota Hilux '89 2.2 (4Y) EFI D/C 4x4, Mikem Suspension, PowerFlow Exhaust, BroSpeed Branch, 31" M/T, Long Range Fuel Tank, Front Diff-Lock
- Real Name: Stephan
- Club VHF Licence: X108
- Location: Parow
Re: How to put your SFA's headlights onto relays.
All I can say is WOW!!!!
Believe it or not, but I only got to try my new headlights for the first time this weekend at the Bridgestone night challenge (two months after I installed them
) I was a bit scared doing the challenge without nice spotlights, but not once I needed anything other than my new headlights!!!!
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
Believe it or not, but I only got to try my new headlights for the first time this weekend at the Bridgestone night challenge (two months after I installed them
![Angel :angel:](./images/smilies/icon_angel.gif)
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
Stress:
The confusion created when one's mind overrides the body's desire to choke the living $H!t out of some asshole that desperately deserves it!
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
![Irate :irate:](./images/smilies/ireful.gif)
![Image](http://i43.tinypic.com/24x0488.jpg)
![Image](http://i54.tinypic.com/xnrw9s.jpg)
-
- High Range 4WD
- Posts: 87
- Joined: Tue Mar 26, 2013 8:25 am
- Town: Cape Town
- Vehicle: Lumina
- Real Name: Nicholas
Re: How to put your SFA's headlights onto relays.
Just installed this loop/harness and what a differencepietpetoors wrote:For those who cannot wait for us to manufacture the fix, I added it to my shop so long.
I've put it up at a lower price as originally planned. When we get the fix we will sell it is a separate plugin unit for the vehicle which need it.
The harness is at
http://www.4x4direct.co.za/shop/index.p ... cts_id=394" onclick="window.open(this.href);return false;
![Celebrate :celebrate:](./images/smilies/celebrate3.gif)
- pietpetoors
- Moderator
- Posts: 10650
- Joined: Thu May 17, 2007 9:12 pm
- Town: Langebaan
- Vehicle: 2.7 Hilux 4x4 DC
- Real Name: Pieter
- Club VHF Licence: X27
- Contact:
Re: How to put your SFA's headlights onto relays.
Spots working or not working?
If NOT working, and if your spots are wired via a relay, move the power wire which activates the relay to the blue wire on the H4 Harness. That should fix it.
If NOT working, and if your spots are wired via a relay, move the power wire which activates the relay to the blue wire on the H4 Harness. That should fix it.
Only Dead Fish Go With The Flow!
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
![Image](http://www.4x4direct.co.za/4x4direct-comm.jpg)
1999 Hilux 2.7i 4x4 Raider DC with 3.4 Prado V6. Rear diff-lock, Bull Bar and rock sliders, 31" Cooper ST Maxx, Snorkel, Alu-Canopy, VHF Motorolla radio, West Coast Rust, Mikem Suspension, Ball Joint Spacers in front and Mikem extended shackles at the rear, 25watt LED Spots
-
- High Range 4WD
- Posts: 87
- Joined: Tue Mar 26, 2013 8:25 am
- Town: Cape Town
- Vehicle: Lumina
- Real Name: Nicholas
Re: How to put your SFA's headlights onto relays.
Sorry not working. Thanks for the info!
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
-
- High Range 2WD
- Posts: 13
- Joined: Wed Aug 05, 2015 11:49 am
- Town: Durban
- Vehicle: Nissan Hardbody & Patrol
- Real Name: Tejan
Re: How to put your SFA's headlights onto relays.
thanks for the tips and tricks